Huber worldwide

Select your Region and Language
Worldwide
Worldwide
Europe
Germany
France
Great Britain
Spain
Switzerland
Sweden
Finland
Norway
Czech
Russia
Poland
Hungary
North America
USA
Australia
Australia
South and Central America
Mexico
Chile
Peru
Brazil
Asia and Middle East
Turkey

Cost-efficient, low wear: HUBER Screw Press Q-Press® in Finland

Maintenance costs caused by wear often impair the economic efficiency of centrifuges. Screw presses offer clear advantages in terms of costs and availability. But the operators of screw presses additionally benefit from other advantages.

Decanter centrifuges are one of the most frequently used systems for sewage sludge dewatering. Their well known advantages, such as high dewatering degrees even with high throughputs, are due to the effect of the separation of heavy solids and the lighter water phase in the centrifugal environment with the three thousandfold of the gravitational acceleration. A drum rotation between 2,000 and 4,000 rpm is necessary to create such a strong centrifugal environment. Such a high rotation leads to abrasion and wear inside the centrifuge.

As, due to wear, such fast running units can be a safety risk for the operating staff, centrifuges should be equipped with systems that monitor vibrations and the temperature of bearings. In addition the limitation of drum speed should be regulated. This will not avoid wear but ensure that wear is reliably detected.

Also the dismounting of centrifuges at regular intervals by specialists contributes to high operating costs. In many markets this sort of wear test is even prescribed. Maintenance of a worn centrifuge usually includes the repair of the drum, renewal of the wear protection on the rotor and a bearing test. Also the sealing surfaces are renewed before the plant parts are balanced on a test stand. The costs for all these measures can easily amount to 10,000 € or more. Besides, this time-consuming and material-intensive work usually cannot be executed on site with the result of longer centrifuge shutdowns and possibly additional costs for bridging the shutdown periods by commissioning subcontractors.

Increasing Maintenance Costs Lead to Searching for Alternatives

The operators of STP Hämeenlinna in Finland experienced exactly the same scenario as described before. Due to increasing maintenance costs and frequent failures due to wear they wanted to relace the centrifuge they had installed six years before. It has been well known in Scandinavia for years that HUBER Screw Presses cause far less maintenance costs that decanters. The reason for the low abrasion is the low rotational speed of the Screw Presses, which is < 1 rpm.

The analysis of the sludges in the HUBER laboratory showed satisfactory guarantee values, e.g. cake DR contents > 28% with a throughput of 200 kgDR/h and a polymer consumption of 9 g/kgD. In addition, the numerous HUBER reference installations in Finland reinforced their decision to choose a HUBER Screw Press Q-PRESS® size 620.

All guarantee values were met already during the first provisional start-up: With a polymer dose of 8 g/kgDR and a solids throughput of 280 kgDR/h DR contents of 33 % were measured. These values were even better than the performance data achieved by the six year old centrifuge on site with a low load and optimal settings. But whereas the centrifuge consumes 12 kW to achieve these performance data and shows a noise level in excess of 86 dB(A), the Screw Press needs only 1 kW with a noise level below 68 dB(A).

Besides, a performance test proved that the Screw Press achieves significantly higher dewatering results: We wanted to maximize throughput and minimize polymer consumption. In fact, the Q-PRESS® 620 achieved an unbelievable cake DR of 38.5% with a solids load of 350 kgDR/H and a polymer dose of 6.5 g/kgDR – a far better result than that achieved by the centrifuge.

Siginficantly Decreased Maintenance Costs

It remains to be seen in how far maintenance costs will decrease in Hämeenlinna which were the decisive factor for the customer to buy the HUBER product. On the basis of the experience we have made over many years with our HUBER Screw Press Q-PRESS® units, however, we expect savings of 70 to 80% compared to the centrifuges.

HUBER Screw Press Q-PRESS® 620 beside the maintenance-prone decanter
HUBER Screw Press Q-PRESS® 620 beside the maintenance-prone decanter
Centrifuge rotor on the balancing stand
Centrifuge rotor on the balancing stand
Dewatered sewage sludge from the Q-PRESS® 620 screw press
Dewatered sewage sludge from the Q-PRESS® 620 Screw Press

Contact

If you have any questions, please do not hesitate to contact us!

We welcome your enquiries and want to offer you the best possible support for your projects.

  Search   Contact   Request